triocm.blogg.se

1. Duplicate annihilator for mac how to#
2. Duplicate annihilator for mac serial#
3. Duplicate annihilator for mac code#
4. Duplicate annihilator for mac download#
5. Duplicate annihilator for mac mac#

Duplicate annihilator for mac download#

Once the bitstream containing at least a minimally configured hardware system has been downloaded to the FPGA, XMD is used to download the cross-compiled U-Boot to the MicroBlaze soft processor:

Loading and running U-Boot Downloading U-Boot to MicroBlaze Now that U-Boot and the toolchain are configured correctly, we can cross-compile U-Boot: Instructions on obtaining and setting up the newest cross-compilation toolchain for MicroBlaze may be found at Microblaze GNU Tools. Xilinx's MicroBlaze GNU toolchain will be used to cross-compile U-Boot for MicroBlaze. Import these two files generated by the U-Boot BSP in SDK into the U-Boot directory for MicroBlaze located at /board/xilinx/microblaze-generic/. The U-Boot compilation will use the definitions and flags defined in config.mk and xparameters.h. The repository is u-boot-xlnx and the branch is master: The U-Boot source tree can be downloaded from the Xilinx Git server. Once the U-Boot BSP has been compiled in SDK, the generated files, config.mk and xparameters.h, can be found at /uboot_bsp_0/microblaze_0/libsrc/uboot_v*/. These selections are made in the fields/drop-down menus located in the 'Settings' of the newly created U-Boot BSP. In order for the U-Boot BSP to generate the necessary settings for U-Boot, it needs to know which specific peripherals should be used for some corresponding tasks. This information is generated by the U-Boot BSP.įirst, download the U-Boot BSP source Once it has been installed and the project has been exported to SDK, the U-Boot BSP can be created for the system. To build U-Boot correctly, some information about the system will need to be provided to the U-Boot build tree. U-Boot includes capabilities of writing to/reading from flash and also transferring files over a network if the available hardware is present:Įthernet lite configured to use interruptsĮthernet configured to use interrupts and DMAĪdditional peripherals and features are considered outside the scope of this page.īuilding U-Boot Creating the BSP required by U-Boot

Duplicate annihilator for mac serial#

Serial output configured to use interrupts MicroBlaze processor configured for '(Low-end) Linux with MMU' Make sure the following peripherals are included in the system: U-Boot requires some minimal hardware configuration. Tests were done on Spartan 605 (PLB and AXI) and Kintex 705 (AXI) evaluation platforms using XPS 14.2 and 14.3.

The timer counter and interrupt controller were also tested. The devices that have been tested include UART lite, UART 16550, Linear flash, EMAC lite, LL TEMAC with PLB DMA, and AXI EMAC with AXI DMA.

Duplicate annihilator for mac code#

U-Boot for MicroBlazeThe Xilinx U-Boot project is based on the source code from git: To make mkimage available in other steps, it is recommended to add the tools directory to your $PATH. Additionally in the tools/ directory the 'mkimage' utility is created, which is used in other tasks to wrap images into u-boot format. Xilinx u-boot supports the following targets:Īfter the build process completes the target u-boot elf-file is created in the top level source directory, named 'u-boot'. The first step is to configure the sources for the intended target. Task DescriptionAll commands have to be executed in your u-boot source directory. Please build the dtc tool before proceeding with the steps described below. U-Boot depends upon an externally build device tree compiler (dtc) in order to build successfully. Building the U-Boot bootloader is a part of the Xilinx design flow described in Getting Started.

Duplicate annihilator for mac how to#

This how-to describes how to build the u-boot bootloader for your target platform. The TEMAC core is delivered through Vivado Design Suite and is part of the comprehensive suite of Xilinx Ethernet solutions. The Xilinx Tri-Mode Ethernet MAC, combined with the Ethernet 1G/2.5G PCS/PMA or SGMII core, provides a complete and highly flexible solution for the implementation of Ethernet Link and Physical layers and is available as a single IP through AXI 1G/2.5G Ethernet. In 10/100 Mbps mode, the TEMAC uses the MII interface. In 1000 Mbps mode, the TEMAC core can also connect with industry standard PHY devices.

In 1000/2500Mbps mode, the TEMAC connects to the Xilinx 1/G2.5G PCS/PMA. The TEMAC core is designed to the IEEE 802.3 specification and operates in 2500 Mbps, 1000Mbps, 100 Mbps, and 10 Mbps modes. The customizable TEMAC core enables system designers to implement a broad range of integrated Ethernet designs, from low cost 10/100/1000 Mbps Ethernet to higher performance 2.5 Gigabit ports.

Duplicate annihilator for mac mac#

The Xilinx Tri-Mode Ethernet MAC core is a parameterizable core ideally suited for use in networking equipment such as switches and routers.